V	15	A	4	R	S	B	-D2
Model	Delivery (mℓ/rev)	Control types	Pressure adjusting range	Shaft rotating(view from shaft end)	Shalt extension	Port pesition	Solenoid valve voltage
V	Refer to specification	Refer to specification A,B,C,D, E,F,G,H	Refer to specification	R:Clockwise  L:Counter-clockwise	no remarks:flat Key S:Spline Special Products	no remarks：Left out of the oil B：After handing out the oil （Specialties）	no remarks： No solenoid valve D2： DC24V A25：220V/50HZ A15：110V/50HZ
Remarks：Shaft  V15：ø19.05；V23、V38：ø22.23；V50、V70：ø31.75

Model	Max.Pressure mpa	Delivery	Delivery of unloading (ℓ/min)		Pressure adjusting range	Speed range		Weight kg
		(mℓ/rev)	1500rpm	1800rpm		Max	Min	Flange type
V15	25	15.0	22.5	27.0	1:8-70 2:15-140 3:20-210 4:20-250	1800	500	11.5
V18	25	17.8	26.7	32.0		1800	500	11.5
V23	25	23.0	34.5	41.4		1800	500	20.0
V38	25	37.8	56.7	68.0		1800	500	23.0
V50	14	51.5	77.2	92.7		1800	500	50.0
V70	14	69.7	104.5	125.4		1800	500	55.0
V15-15	25	15/15	22.5/22.5	27/27		1800	500	24
V23-23	25	23/23	34.5/34.5	41.4/41.4		1800	500	40
V15-38	25	15/37.8	22.5/56.7	27/68		1800	500	36.5
V38-38	25	37.8/37.8	56.7/56.7	68/68		1800	500	49
V15-70	Small pumps 25，Big pumps 14	15/69.7	22.5/104.5	27/125.4		1800	500	69.5
V38-70	Small pumps 25，Big pumps 14	37.8/69.7	56.7/104.5	68/125.4		1800	500	78
Remarks： øV50 normally replaced with the V70, V50, when if it must take special orders. øV50, V70 instantaneous pressure up 25PMa, long working pressure should be less than the 14PMa.

Control	Symbol	Curve	Feature
A:Pressure Compensator Control			1、The system pressure increased near the threshold voltage adjustment, the pump flow down automatically, the pressure to maintain constant。 2、Flow and pressure limiting pressure can be manually adjusted.
B:Multi-stage Flow&single-stage Pressure Control (With cyinder)			1、Flow can be from 0 to maximum, from the biggest transferred minimal, making multi-segment changes, pressure to maintain set pressure. 2、Making machinery in the rise and fall with the buffer to prevent collision, vibration, suitable for dedicated machines, lifting crane.
C:Flow Control Type			1、A low-pressure high-volume, high pressure low flow rate of the high and low pressure pump function, optional low-power of the engine. 2、The system pressure increased, close to the pre-adjustment of the "PL" limited pressure, the pump flow automatically down "QL"。 3、Pressure "PH, PL", and flow "QH, QL" can be arbitrarily adjusted, respectively. 4、Apply to air travel long travel a short mechanical pressure, speed, provincial and horsepower.
D:Seolenoid controlled pressure compensator type with unloading Device			1、A type of pressure compensation control to increase pressure relief function. 2、A long time for relief situation. 3、System downtime, through the pump pressure relief operation, oil temperature and noise can maintain a lower level.
E:Dual pressure control by Solenoid Operated Valve			1、According to the electromagnetic valve to control the high and low pressure limit of two different pressure 2、Suitable for a constant speed brakes and set the use of two working pressure。 3、PL and PH may be optional side as a high-pressure valve。
F:2Flow-2pressure p.c.by solenoid operated valve			1、Solenoid valve controls a small low-pressure high flow and high pressure function of flow rate。When the solenoid valve gets power, the pressure increases to the PH, flow down to QL。 2、Pressure PL, PH and flow QL, QH can be arbitrarily adjusted。 3、Rapid feed changes applied to a slow feed of the machine tool equipment, etc.
G:Remote pressure compensator control			1、Pressure compensation with the "A" type 2、Remote control to adjust the pressure to do by remote control valve to adjust pressure range
H:Power matching control			1、The pump combination with proportional valve can be used to create an ideal system for energy efficient features。 2、A feedback function to control the amount of oil pump spit, reaching a low oil temperature, the provincial power function. 3、Applicable to the work of machinery "Fast Forward", "slow into the" action to use.
HJ:Load sensing & proportronal elector-hydraulic pilot relief valves.			1、Except for the HJ with the characteristics of the type of pump, and then increase in pressure load-sensing。 2、After the assembly of the electromagnetic proportional pressure into force in accordance with current proportional control, to achieve energy efficient, provincial and horsepower capabilities.
HK:Proportional Electro-hydrauic load sensing type			1、By flow control valve differential pressure before and after a certain value to control pump out the amount of leaf 2、Be able to control the load pressure is constant, while the flow valve control flow in accordance with section size, auto-sensing pump spit out a constant flow of leaf induction, reaching a minimum on the energy function.

Ⅰ、Notes for hydraulic oil selection
*、When the use of pressure below 7MPA , choose the ISO standard VG32 ~ 68 viscosity hydraulic oil or anti-wear hydraulic oil.
*、When the use of pressure above 7MPA , select the ISO viscosity standard VG32 ~ 68 a considerable anti-wear hydraulic oil.
*、Use the following hydraulic oil,please contact Kompass technical department.：Phosphate system，fatty acid esters system，Water, a glycol system，W/Oemulsion、HWBF
Ⅱ、Viscosity and oil temperature
* Using in the viscosity of 15 ~ 400cSt, oil temperature 0 ~ 60 ℃。
Ⅲ、Pump installation and eccentric
* When drive shaft and the eccentric shaft in the 0.05mm below,can not increase the shaft radial force.
* When the axis is inconsistent, it will produce bearings, O-ring damage, noise, vibration, and the reasons for causing pump failure.
* To avoid the chain gears with a belt-driven pumps to the sides.（This is to generate noise and cause bearing damage.）
Ⅳ、Tubing Installation
* To steel for the piping, the installation tube take care not to make rigid eccentric while installation tube.
* Mandatory takeover eccentric, is the biggest reason for the noise.
Ⅴ、Tubing leakage
* Pipeline leaks, and other return pipe can not merge.Oil return alone to maintain the pressure in the pump shell 0.35kgf/cm2 below.
* Return pipe into the fuel tank below the liquid level, as far as possible away from the Oil Pipe Installation
Ⅵ、Notes for start point
* Start pump before it will pump hydraulic oil into the oiling port, when the pump pressure in the crust below 0.35kgf/cm2
* To start, do not rapidly rise to full-speed rotation, the motor switch initially repeated ON-OFF, when the air tubing in continuous operation before discharge. Be sure to buck the state starting in the no-load circuit.
Ⅶ、Rotary direction
* Direction from the shaft side, standard clockwise direction, counter-clockwise is a special product, please note when ordering.
Ⅷ、Oil Pressure
* Oil pressure keep-125mmHg or less
* Oil pressure on a high, then the resulting cavitation. Component damage, noise, vibration, reduced life
Ⅸ、Filter
* Hydraulic oil pollution, is to pump failure and reduced life reasons, please give full attention to hydraulic oil pollution, pollution control, degree-level or less in NAS9
* The purpose of the use of 150 in the Oil filter port; in the main return pipe on the oil filter be sure to use the 25u below; 140kgf/cm2 more occasions, please use the 10u of the oil filter.
Ⅹ、The maximum operating pressure
* The maximum operating pressure of time, as a cycle of 10% or less, hold time of 6 seconds or less.